3 Reasons Why You Should Never Use Tire Sealant to Fix Flats

Tire sealants may seem like a quick fix to repair flat tires when you are stranded on a highway; however, in the long run, it may not be the best solution. Many tire experts suggest avoiding using it to repair the car’s flat tire as much as possible because of the damage it causes to the tire. Here are the three reasons to avoid using it:

It damages the TPMS sensor
A tire-pressure monitoring system, better known as TPMS, is a sensor used in most pneumatic tires to monitor air pressure in various types of vehicles. When you repair your car’s flat tire with a sealant, it clogs your TPMS sensor, damaging it beyond repair.

It’s difficult to clean
While it's easy to use when it comes to fixing a flat, it’s way harder to clean when you finally repair your tire properly at a repair shop. And when it isn’t cleaned promptly, it leaks in and destroys the TPMS.

Corrode the wheel
When you don’t clean the tire sealant on time after fix-a-flat, it leaks in and causes damage to the overall integrity of the wheel and corrodes it over time. As a result, you have to go through costly repair and most of the times, you have to replace the tire.

Bottom line
If you want your car’s tire to last long, make sure you stop using tire sealants to fix flats. The best course of action is to use the best flat tire repair kit that gets the job done in a jiffy.



Comments

Post a Comment

Popular posts from this blog

How To Use An Air Compressor On Your Flat Tire?

Image
Experiencing a flat tire at the most inconvenient time can happen to anyone and anytime. To ensure that the tire pressure is correctly maintained, you’ll need the assistance of an air compressor. An air compressor is a device that converts power (using an electric motor or engine) into potential energy stored in compressed air. This blog will provide you with the essential tips on how to use an air compressor for flat tire . #1 Know the Tire Pressure You must have the information on how much pressure must go into the tire. The exact amount might vary so, it a good idea to check the vehicle’s manual for the proper tire pressure amount. #2 Get the Tire Ready Each tire should have a stem cap attached to the top of the valve stem. Remove the cap and put it to the side, but make sure you don’t misplace it. #3 Turn on the Air Compressor Typical air compressors depend on electrical power. Plug in the air compressor to let it accumulate with air. Smaller units have a t...
Read more

Avoid Stress Of Road Emergencies - Purchase Tire Changing Tools For Your Motorcycle

Image
Getting stranded on the side of a long stretch of highway is far from someone's imagination. If you have ever had a flat tire then you must know the agony of not having automobiles passing by to help you out with the tire rendered useless due to unforeseen circumstances. Having the right tools is important to prevent the isolation of being stranded and managing the problem of such emergencies. An emergency flat tire repair kit is the best thing you could have on your journey if you have rallied up a lot of miles on your odometer. As an automobile gets older, it becomes susceptible to engine failures, poor alignment and punctured tires. Avoid Flat Tire Situations With These Tips Usually, due to excessive friction that has worn out the tires, there are many cases of flat tires. Here's how to ensure you don't get stranded due to a rusty nail or a piece of misfortune: Check the tire pressure regularly. Check your tire pressure in the morning, before you’ve ...
Read more

9 Primary Steps To Change a Flat Tire For Beginners

When you have the basic items that are required to change or fix a flat tire, you can get out an otherwise situation, reducing greatly the potential damage to your tires. That being said, what if you don’t know how to use the best flat tire repair kits available to you? Read the information listed below on how you can fix a flat tire, and other related useful information to change the tire. Park the vehicle and use hazard lights. Brace the tires to prevent stability and increase stability. Identify spare tire and jack. The vehicle’s manual can be used for this. Position the jack and then jack up the vehicle. Take out all the hubcaps and loosen the lug nuts. After making sure the jack is fully stable, remove the tire. Attach the spare tire and place the lugs nuts in the correct position. Tighten the lug nuts by using the tire wrench (clockwise direction). Examine the lug nuts after driving. After driving for some covering few miles on the road, it is a wise decision to ha...
Read more